1. 如何将“工夹模具”译成英文
The clamps mold (工夹模具)
还有一些相关的词语,可以看看:)~
模具零件:mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
耐磨板/油板:wedge wear plate
压条:plate
ejector leader busher顶出导销(顶出板导杆)的衬套,也叫ejector guide bush
ejector stopper,用于顶出制动的,或限位的
ejector pin retaining plate:顶针固定板。
气纹:gas mark
2. 翻译英语,模具方面的
一:流道: runner
��
热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner
��
唧嘴直流: direct sprue gate 圆形流道:round(full/half runner
��
流道电脑分析:mold flow analysis 流道平衡:runner balance
��
热嘴: hot sprue 热流道板:hot manifold
��
发热管:cartridge heater 探针: thermocouples
��
插头: connector plug 插座: connector socket
��
密封/封料: seal
二:模具零件: mold components
三板模:3-plate mold 二板模:2-plate mold
边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing
��
中托司:shoulder guide bushing 中托边L:guide pin
��
顶针板:ejector retainner plate 托板: support plate
��
螺丝: screw 管钉:dowel pin
��
开模槽:ply bar scot 内模管位:core/cavity inter-lock
��
顶针: ejector pin 司筒:ejector sleeve
��
司筒针:ejector pin 推板:stripper plate
��
缩呵:movable core,return core core puller
��
扣机(尼龙拉勾):nylon latch lock 斜顶:lifter
��
模胚(架): mold base 上内模:cavity insert
��
下内模:core insert 行位(滑块): slide
��
镶件:insert 压座/斜鸡:wedge
��
耐磨板/油板:wedge wear plate 压条:plate
��
撑头: support pillar 唧嘴: sprue bushing
��
挡板:stop plate 定位圈:locating ring
��
锁扣:latch 扣鸡:parting lock set
��
推杆:push bar 栓打螺丝:S.H.S.B
��
顶板:eracuretun 活动臂:lever arm
��
分流锥:spure sperader 水口司:bush
��
垃圾钉:stop pin 隔片:buffle
��
弹弓柱:spring rod 弹弓:die spring
��
中托司:ejector guide bush 中托边:ejector guide pin
��
镶针:pin 销子:dowel pin
��
波子弹弓:ball catch
三,模具成形不良用语英汉对照
aberration 色差 bank mark 料纹 bite 咬入
blacking hole 涂料孔(铸疵) blacking scab 涂料疤
blister 起泡 blooming 起霜
low hole 破孔 blushing 泛白
body wrinkle 侧壁皱纹 breaking-in 冒口带肉
bubble 膜泡 burn mark 糊斑
burr 毛边 camber 翘曲
cell 气泡 center buckle 表面中部波皱
check 细裂痕 checking 龟裂
chipping 修整表面缺陷 clamp-off 铸件凹痕
collapse 塌陷 color mottle 色斑
corrosion 腐蚀 crack 裂痕
crazing 碎裂 crazing 龟裂
deformation 变形 edge 切边碎片
edge crack 裂边 fading 退色
filler speak 填充料斑 fissure 裂纹
flange wrinkle 凸缘起皱 flaw 刮伤
flow mark 流痕 galling 毛边
glazing 光滑 gloss 光泽
grease pits 污斑 grinding defect 磨痕
haircrack 发裂 haze 雾度
incrustation 水锈 indentation 压痕
internal porosity 内部气孔 mismatch 偏模
mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面缺陷
overflow 溢流 peeling 剥离
pit 坑 pitting corrosion 点状腐蚀
plate mark 模板印痕 pock 麻点
pock mark 痘斑 resin streak 树脂流纹
resin wear 树脂脱落 riding 凹陷
sagging 松垂 saponification 皂化
scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划痕
scuffing 深冲表面划伤 seam 裂痕
shock line 模口挤痕 short shot 充填不足
shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折叠 straightening 矫直
streak 条状痕 surface check 表面裂痕 surface roughening 橘皮状表皮皱折 surging 波动
sweat out 冒汗 torsion 扭曲 warpage 翘曲 waviness 波痕
webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皱纹
各式模具分类用语英汉对照
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模 landed positive mold 有肩全压式模具
button die 镶入式圆形凹模 loading shoe mold 料套式模具
center-gated mold 中心浇口式模具 loose detail mold 活零件模具
chill mold 冷硬用铸模 loose mold 活动式模具
clod hobbing 冷挤压制模 louvering die 百叶窗冲切模
composite dies 复合模具 manifold die 分歧管模具
counter punch 反凸模 modular mold 组合式模具
double stack mold 双层模具 multi-cavity mold 多模穴模具
electroformed mold 电铸成形模 multi-gate mold 复式浇口模具
expander die 扩径模 offswt bending die 双折冷弯模具
extrusion die 挤出模 palletizing die 叠层模
family mold 反套制品模具 plaster mold 石膏模
blank through dies 漏件式落料模 porous mold 通气性模具
duplicated cavity plate 复板模 positive mold 全压式模具
fantail die 扇尾形模具 pressure die 压紧模
fishtail die 鱼尾形模具 profile die 轮廓模
flash mold 溢料式模具 progressive die 顺序模
gypsum mold 石膏铸模 protable mold 手提式模具
hot-runner mold 热流道模具 prototype mold 雏形试验模具
ingot mold 钢锭模 punching die 落料模
lancing die 切口模 raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具 sectional die 拼合模
runless injection mold 无流道冷料模具 sectional die 对合模具
segment mold 组合模 semi-positive mold 半全压式模具
shaper 定型模套 single cavity mold 单腔模具
solid forging die 整体锻模 split forging die 拼合锻模
split mold 双并式模具 sprueless mold 无注道残料模具
squeezing die 挤压模 stretch form die 拉伸成形模
sweeping mold 平刮铸模 swing die 振动模具
three plates mold 三片式模具 trimming die 切边模
unit mold 单元式模具 universal mold 通用模具
unscrewing mold 退扣式模具 yoke type die 轭型模
机械类常用英语:冲压模具-零件类
punch冲头 insert入块(嵌入件)
deburring punch压毛边冲子 groove punch压线冲子
stamped punch字模冲子 round punch圆冲子
special shape punch异形冲子 bending block折刀
roller滚轴 baffle plate挡块
located block定位块 supporting block for location 定位支承块
air cushion plate气垫板 air-cushion eject-rod气垫顶杆
trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子
guide plate定位板 sliding block滑块
sliding dowel block滑块固定块 active plate活动板
lower sliding plate下滑块板 upper holder block上压块
upper mid plate上中间板 spring box弹簧箱
spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板
bushing bolck衬套 cover plate盖板
guide pad导料块
机械类常用英语:冲压模具-模板类
top plate上托板(顶板) top block上垫脚
punch set上模座 punch pad上垫板
punch holder上夹板 stripper pad脱料背板
up stripper上脱料板 male die公模(凸模)
feature die公母模 female die母模(凹模)
upper plate上模板 lower plate下模板
die pad下垫板 die holder下夹板
die set下模座 bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板)
outer stripper外脱料板 inner stripper内脱料板
lower stripper下脱料板
冲压模具-冲压名称类英汉对照
plain die简易模 pierce die冲孔模
forming die成型模 progressive die连续模
gang dies复合模 shearing die剪边模
riveting die铆合模 pierce冲孔
forming成型(抽凸,冲凸) draw hole抽孔
bending折弯 trim切边
emboss凸点 dome凸圆
semi-shearing半剪 stamp mark冲记号
deburr or coin压毛边 punch riveting冲压铆合
side stretch侧冲压平 reel stretch卷圆压平
groove压线 blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印 tick-mark farside反面压印
extension dwg展开图 procedure dwg工程图
die structure dwg模具结构图 material材质
material thickness料片厚度 factor系数
upward向上 downward向下
press specification冲床规格 die height range适用模高
die height闭模高度
gap间隙 punch wt.上模重量
3. 模具方面的一段翻译 (英译中)
手译的,还望各位高人指点
In fabricating the mould, some preparations are needed. The capability of the machine that are available in faculty are investigated. The machines that required in fabricating the mould are drilling machine, milling machine and grinding machine. The plastic injection moulding machine is also needed for producing the product. The machine that has been used is BOY 22D. Besides that, it is also required to search and purchase the mould base, which can fit the injection moulding machine. Carbon steel AISI 1050 had been selected as material for the mould base. Since some components such as ejector pin, locating ring, sprue bush, water junctions and springs are not included in the mould base, these components are purchased independently. The plastic material that has been used is ABS.
制造模具时,准备工作是必须的。可用设备的生产能力已经被调查过了。制造模具需要的机器有钻床,铣床和磨床。生产这个项目时注塑机也是必须的。设备的型号是BOY22D。除此之外,也需要寻找和购买适合注塑机的模架。Carbon steel AISI 1050最终被选为制作模架的原材料。由于某些原件诸如顶针、定位环、浇口套、弹簧等是不包含在模架里的,因此需要单独购买。注塑原材料使用的是ABS。
3. Mould design
There are four design concepts that can be used in this project. The description of these design concepts is as follows:
(a) Three-plate mould—Having two parting lines with single cavity.
(b) Two-plate mould—Having one parting line with single cavity without gating system.
(c) Two-plate mould—Having one parting line with double cavities with gating system and with ejector pin at the cavities.
(d) Two-plate mould—Having one parting line with double cavities with gating system and without ejector pin at the cavities.
3.模具设计
四种设计理念可用于设计此项目。描述如下:
(a) 三板模—— 一穴两分型面
(b) 二板模—— 一穴一分型面不带浇注系统
(c) 二板模—— 两穴一分型面,带浇注系统和顶针
(d) 二板模—— 两穴一分型面,带浇注系统,不带顶针
Since this project is limited in budget, the type of mould base that has been chosen is two plate mould instead of three plate mould. Among the design concepts for two plate mould, the concept ‘d’ has been chosen. This is because concept ‘b’ is non-productive while concept ‘c’ may damage the product during ejection.
由于项目预算有限,模架的型号由二板模取代了三板模而最后被采纳。在二板模的多个设计理念中,d理念最后被采纳,这是因为b理念无法用于实际生产,而c理念在注塑成型时有可能会损坏产品。
Generally, two plate mould consist of eight plates and there are their standard dimensions, respectively. The mould base that has been chosen must base on the specification of the injection moulding machine that will be used. In this project, the standard mould base with 250 mm × 250 mm has been used and its plates dimension are shown in Table 1.
通常的,二板模由八个板组成且它们都有各自的标准尺寸。模架的选择必须要依据将要使用的注塑机的标准。针对这个项目,标准模架的型号是2525(250 mm × 250 mm),它的各个板的尺寸已在表格1中列示。
4. 求英文翻译4,谢谢
排气槽一般不须因注塑模具提供足够的可能性,通过模具板和ejectors让 空中逃跑. 瓶帽或关闭侧注入部分代表要求宣泄. 关于注射inrushing造型材料,形成了环城的核心和时尚. 有没有可能空中逃脱; 它是压缩的最高点, 有碍观瞻造成烫伤的痕迹,以致于部分瘫痪. 风口是人生的无花果. 39的额外加装了排气针. 随后的标记可成花纹. 大部往往不能剥去模具的核心,因为他们是保留的吸力. 在这种情况下核心必须配备有排气蘑菇阀 它也可以作为喷射器(图40). 排气蘑菇可以负起全部的根据地回合moldings. 12闭锁装置的单型腔模具,其中部分产品是由中央通过注入绝缘spruebushing 部分自动degated了春季行动(图15). 隧道的门也是切掉了一部分由参赛者在射出成型(17.4%和21). 这种模具挤提自动运行. 有针对性地门几乎所有地区都可以degated在一个三板模和模具可以经营 完全自动. 但即使部分适合隧洞浇注可以自动degated在塑造一个双板模. 图41解释degating进程模具幻灯mounts. 转轮(一)接受塑料材料直接从绝缘spruebushing(二). 这转轮(一)保持尽可能小. 为避免二次手术,部分切掉转轮. 这个剪切过程中的收益情况如下: 注塑机组背序幕spruebushing(二)在模具开幕剖切线(1). 该spruebushing(乙)推到了外面的泉水(二),将它从跑步(一). 同时切套管(三)移至右侧有力的弹簧压力(d)和隔离部件 转轮(一). 在开幕模具零部件所喷出的顶杆(j)和转轮(一)由sprue喷射 (k)分开. 它建议增加直径的spruebushing(b)在位置(五)approx. 0.05毫米保护刃口切套管. 当moldcloses, 推回pins(g)归还射板(j)含有顶杆(六)与spruepullerpin(k) 到出发位置.
5. 急需一篇有关冲压的中译英文献啊 谁有的帮忙下啊 不胜感激
冲压常用英文单词
英文 中文
plain die 简易模
pierce die 冲孔模
forming die 成型模
progressive die 连续模
gang dies 复合模
shearing die 剪边模
riveting die 铆合模
draw 抽引
bending 折弯
trim 切边
emboss 凸点
dome 凸圆
semi-shearing 半剪
stamp mark 冲记号
deburr or coin 压毛边
punch riveting 冲压铆合
side stretch 侧冲压平
reel stretch 卷圆压平
groove 压线
blanking 下料
stamp letter 冲字(料号)
shearing 剪断
tick-mark nearside 正面压印
tick-mark farside 反面压印
extension dwg 展开图
procedure dwg 工程图
die structure dwg 模具结构图
material 模具材质
material thickness 料片厚度
factor 系数
upward 向上
downward 向下
press specification 冲床规格
die height range 适用模高
die height 闭模高度
burr 毛边
gap(freedom) 间隙
weight 重量
total wt. 总重量
punch wt. 上模重量
separation 分割
parting surface support balance 承压平面平衡
parting line venting 模排气
return pin and cavity interference 回针碰料位
mold base shut hight 模总高超出机台规格
water line interferes withejector pin 顶针碰运水
part from cavith (core) side 料位出上/下模
cavity direct cut on A-plate,core direct cut on B-plate. 模胚原身出料位
Do not use (core/cavity) insert 不准用镶件
use beryllium copper insert 用铍铜做镶件
preliinary (final) mold design 初步(正式)模图设计
reverse core 反呵
spring compressed length 弹簧压缩量
good stability,stable 稳定性好
insufficient rigidity 强度不够
even cooling 均匀冷却
sticking 锁模
thero expansion 热膨胀
tolorance 公差
copper electrode 铜电极
wire cut edm 电火花线割
cam block 滑块(机构)
demagnetization 去磁;消磁
parameter 参数
shim(wedge) 楔子
slug hole 废料孔
quenching 淬火
tempering 回火
annealing 退火
shank 模柄
inserted die 镶块
bushing block 衬套
crank shaft 曲柄
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢
marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢
molybdenum steel 钼钢
nickel chromium steel 镍铬钢
prehardened steel 顶硬钢
silicon steel sheet 硅钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
mold components 模具零件
3-plate mold 三板模
2-plate mold 二板模
leader pin/guide pin 边钉/导边
bushing/guide bushing 边司/导套
ejector guide bush 中托司
ejector guide pin 中托边
ejector retainner plate 顶针板
support plate 托板
upper die base 上模座
lower die base 下模座
upper supporting blank 上承板
upper padding plate blank 上垫板
spare dies 模具备品
magnesium 镁
Aluminum 铝
Aluminum-magnesium alloy 镁铝合金
torch-flame cut 火焰切割
lathe 车
mill 锉
plane 刨
grind 磨
drill 钻
boring 镗
6. 塑胶模具中,谁来帮我说说,导柱,大拉杆,小拉杆的作用,以及之间的关系,为什么三板模中。
两板模: 模具类型
上隔热板:
上固定板:
公模板: 后模模块固定板
母模板: 前模模块固定板
上顶针板: 出模顶针板
下顶针板: 出模顶针固定板
模脚:
下固定板:
下隔热板:
零件:
定位环:
灌嘴: 又叫咀嘴,射胶嘴,射胶用
导柱: 格林柱,前后模连接,保持一致的运动方向
母模仁: 装在母模板上的模块,成形产品前模形装
公模仁: 装在公模板上的模块,成形产品后模形装
回针:
弹簧: 使顶针板回位
顶针: 装在顶针板上,使产品出模
限位块: 避免过度冲撞损坏模具
支撑柱:
顶针板导柱: 平衡顶针板的运动方向
顶针板导套: 和导柱配套,作用一样
垃圾丁: ,帮助产品和流道开模后被带到后模,然后通过顶针顶出产品
O型环: 上下模具的吊环
三板模: 模具的一种类型,适合浇口在前模板,产口小水口的进胶方式
三板模与两板模相比多了快脱料板:多的胶料板就是前模浇道的脱模
脱料板:帮助前模浇道从射嘴中脱出
7. 请问有人能帮我说下模具中三板模的基本结构吗?
面板,水口板,前模板,组成定模,后模板,后模垫板,顶针面板,顶针板,垃圾钉板,模脚和底板组成动模,这种模具在注塑模中应用较多,一般试用与产品表面要求不允许有胶口印的模具,采用点进胶。
8. 帮我翻译下摘要
人工翻译 谢谢 希望采纳
Abstract: Compared with traditional injection mold design method, based on UG and Moldflow injection mold design and the design cycle is short, low cost and good mold manufacturing process. Part of this project is designed to hang air panel. First of all the parts using computer-aided modeling software UG and injection mold design, the design of the parts of the structure and process analysis, injection mold design into a three-plate mold, a mold of a cavity-shaped shunt, angle pin core pulling bodies and Pulling lifters body type screws be placed away from the hook body. Mold will use the AutoCAD drawing session on the assembly drawing and part drawings for repair. Then mold flow analysis software Moldflow of the best parts of gate location and filling + Cooling + warpage analysis, based on the analysis of the cooling system and the gating system to adjust and optimize the injection mold can be adjusted accordingly. Finally, a reasonable injection mold casting system, cooling system, the cooling effect is good, the overall structure of the mold and reasonable.
Keywords:UG Moldflow injection mold